Floor Drying, Wall & Ceiling Flood Damage Equipment

The HP-PLUS Floor Drying Package is the improved version of Injectidry's HP60i Floor Drying package. This unit is quieter (less than 60 dB), more powerful, and easier to set up than the original. You can use up to 12 Multi-Port or 20 8-Port Vac-It panels with an increase up to 30% in drying capabilities. 

The HP-PLUS Wall and Ceiling Drying Package is the improved version of Injectidry's HP60i wall and ceiling package. This unit is quieter (less than 60 dB), more powerful, and easier to set up than the original.

Dry walls without damage! The Dri-Eaz DriForce InterAir Drying System dries almost anywhere: ceilings, behind cabinets, beneath built-ins, insulated walls, firewalls, & vinyl-covered walls. Can be used on positive or negative air pressure.

The WolfPack Floor Drying System from Dri-Eaz connects to the AirWolf air mover and directs airflow down along the floor, drying hardwood floors faster than ever. It easily adapts to any floor plan.

The Injectidry HP60 Floor Drying Package is designed specifically for floor drying. This setup is extremely quick, easy, and efficient for your typical floor drying needs.

Injectidry's high-pressure drying systems are specifically developed to target high risk areas of hidden moisture. The HP60i can be used with Vac-It Panels to quickly dry hardwood floors. Capable of drying over 100 linear feet of wall or ceilings.

The AirWolf provides an unbeatable combination of powerful CFM and strong static pressure. Optimized for use with the Dri-Eaz WolfPack hardwood floor drying system, this combo dries wood floors from the bottom out and can help avoid costly repair bills.

The Direct-It “IN” Universal Air Mover Adapter gives you the ability to dry critically damaged areas fast! This handy accessory attaches to most standard centrifugal air movers, and allows you to direct air in as many as 17 different locations and dry up to 22 feet!

The Direct-It Axial Adapter connects to both axial fans and air scrubbers, allowing contractors to direct drying and scrubbing efforts into wall cavities and other areas in need of high air exchange rates. This easy-to-setup system gives you the ability to replace fewer walls, ceilings, and hardwoods.

The TurboVent InterAir Drying System from Dri-Eaz is a handy air mover accessory that will help you dry difficult areas, such as cabinets, cupboards, and walls. Simply attach it to your Sahara air movers and begin ducting air into three different areas at once.

Injectidry Infrared Heating Panels allow restoration professionals to dry areas faster while using significantly less energy. Each panel is designed to directly heat ONLY the wet surface, resulting in dramatically more efficient drying using only 400 watts of energy (roughly 25% of a typical hair dryer!).

Injectidry Vac-It Panels simplify the setup process and significantly reduce your labor costs when drying hardwood floors.

The Dri-Eaz TurboVent 48 fits over the snout of your Dri-Eaz Sahara TurboDryer, redirecting the air over a 48-inch-wide column. This handy accessory is ideal for drying wet walls and ceiling cavities and boosts the effectiveness of your drying equipment.

The Adaptidry achieves high efficiency by dispersing intense drying power simultaneously to multiple areas around the room.

Replacement extra slim, small point Vac-It panels. Each panel measures 7" x 30".

The Injectidry Vac-It Slim Panel is the same length as the full sized Multi-Port Panel, but half the width. You get the same great drying performance for about half the cost!

Injectidry Vac-It Panels simplify the setup process and significantly reduce your labor costs when drying hardwood floors.

Injectidry Vac-It Panels simplify the setup process and significantly reduce your labor costs when drying hardwood floors.

Replacement HP60 base unit only with air out and air in main hoses.

HP60 Plus base unit with air out and air in main hoses

The Water Separator works to protect your HP 60 blower by preventing bulk water from passing through it when drying in a negative mode.

The Silencer is made of ABS plastic and quiets the drying system by about 25%. It reduces some of the impeller noise in addition to the air rush sound. Attaches to the 2-inch OUT trunkline and sets up in seconds.

This 1 1/4" x 50' Direct‐It hoseline roll fits all Direct-It products.

Injectidry's Inline HEPA filtering system stops dirt and debris before it contaminates your equipment and the air.