Prochem Blazer Plus Truck Mount Replacement Parts
-
Ignition CoilThis replacement ignition coil is designed for use in the HydraMaster Boxxer 421 and Prochem Blazer GT/XL/Plus units
-
Waste Tank Filter, 2"F Stainless Steel2"F stainless steel waste tank filter.
- Stainless Steel
- 2"F x 4"D x 10"L
- Waste Tank Filter
- PASS50-2-100
-
TKX Lubricant, 16oz (4KK77)Aerosol blower lubricant. For use with all truckmount and blower types.
- Blower Lubricant
- Non Drying Oily Film
- Displaces Moisture
- Protects Against Corrosion
- For use with All Vacuum Blower and Truckmount TypesÂ
-
Stainless Steel Chemical Pump (100906)
Stainless steel chemical pump by General Pumps.
- Stainless SteelÂ
- Easily RebuildableÂ
- Used On A Wide Variety Of Truck Mount Systems
$200.31 -
Briggs & Stratton Air Filter (30‑430)ea Air Filter for Bruin
-
Truck Mount Pump Out System
Featuring a 12VDC motor this diaphragm waste pumpout produces consistent, smooth pulsation to prevent misdirected wastewater flooding. This pump can be run dry for short periods without causing damage to the pump.
- 0.5HP drive motor
- Diaphragm pump by COMET USA
- For use with any truck mount system
$2,263.57 -
Hose, Winterizing and DescalingTruck mount winterizing and descaling hose kit.
- Winterizing and Descaling Hose
- Provided by Jon-Don
- Free Technical Support
$122.73 -
Brass Adapter, FGH x 3/8"M (194‑C)3/8"MPT x FGH brass adapter.
- Brass
- 3/8"M x FGH
- Adapter
- 89GH126
-
Float Switch, Recovery Tank
This recovery tank level kill switch can also be used as the pump-out activation switch. This switch fits most BLUEline and some HydraMaster units.
- 1 1/2" pipe thread
- Prochem
- HydraMaster
- BlueLine Equipment
- Sapphire ScientificÂ
$189.23 -
Vibration Pad
Vibration Pad
-
Rod, Float Valve/BallWaterbox float ball rod.
- Prochem Float Valve
- Older Rectangle Box
- 1/4-20 x 6"
- Stainless Steel
-
Bypass Manifold Cap
Bypass Manifold Cap
- Cap fits orifice side of bypass manifold
- Brass
Â
-
Bypass Manifold
Brass bypass manifold body only. For older Prochem and BLUEline truck mounts.
- Brass bypass manifold
- Fits most older Prochem and Blueline truck mounts
-
Cable, Choke
Choke Cable
- Choke cableÂ
- Fits all Prochem and BLUEline truck mounts with choke
- Free Technical Support Available
-
Cable, Throttle
Throttle Cable.
- Throttle Cable
- Fits older Prochem units with T-handle throttle
- Free Technical Support
-
GoodYear Matchmaker Belt (AX36)Matchmaker belt AX36.
- AX36
- Blazer Plus
-
GoodYear Matchmaker Belt (AX38)Matchmaker belt AX38.
- AX38t
- BlazerXL/LegendXL/Apex/Boxxer 421,427
-
Pulley, Dual for BlazerPulley Dual for Blazer$213.06
-
O‑Ring Check Valve Assembly
This O-ring goes on the check valve cap and seals the cap to the check valve. Measures 7/8" ID x 1 1/16" OD.
- O-Ring fits cap on older Prochem brass chemical pumps
Â
-
O‑Ring Y‑Strainer
This O-ring is .676 Id x .816 Od. It fits the Y-Strainer for the solution outlet assembly and the bypass manifold assembly for most Prochem and BLUEline units.
-
Gasket Waste Tank Lid
Waste tank lid gasket for older Prochem truck mounts.
- Rubber gasket for most Prochem waste tank lids
- Not for use with Prochem Performer 405
Â
-
Gasket Catalytic Converter
Gasket for catalytic heat exchange system on the older Prochem and BLUEline truck mounts.
- Silver high temp gasket for catalytic heat exchangers
-
Gasket Blower Heat Exchanger
Gasket for blower heat exchanger on most older Prochem truck mounts.
- Rubber gasket for blower heat exchanger
-
Filter, Pre‑Air Kohler
This pre-air filter has been manufactured to fit the following Kohler Command engine-equipped truck mount units: Prochem Legend, Legend SE and Legend XL.
- Pre-filter
Â
