Ninja Dual 2 Stage 200&500 PSI Extractor Replacement Parts
-
Flow Control K‑Valve
This Flow Control K-Valve is rated at pressures up to 500 PSI. This part is easily rebuildable.
- Withstands pressures up to 500 PSI
- Easily rebuildable
-
PumpTec 112T Series Pump Motor Set, 120V (112T‑075/M35‑8)The Pumptec 112T series pump features an efficient plunger-type design that produces up to 20% more pressure or flow for a given power input compared to competitive pumps. This pump is ideal for pressure cleaning, pest spraying, and misting applications.
- Plunger-type design for ultimate pumping efficiency
- 200 PSI
- Four 1/4” ports
- Non-Viton Buna seals
- 120 volt
$471.66 -
PumpTec 207 Series Complete Pump (80547)
This 207 Gold Series pump replaces the 205 series. This complete pump assembly has a 120V, 1/3 HP motor and provides an adjustable 500 PSI. It pumps at a rate of 1.4 GPM at 500 PSI and can withstand a maximum of 160°F of water inlet temperature.
- Replaces 205 series pump
- Adjustable 500 PSI
- Complete pump and motor
- 1/3 HP; 3.0 /1.5 amps
- 1.4 GPM at 500 PSI
$645.85 -
PumpTec 112 Series Pump Head (60002)
Pump Head PumpTec 112 Series without motor.
- PumpTec
- Series 112T Pump Head
- 200 PSI
$275.95 -
PumpTec M35 Pump Motor (M70)
M35 1/7HP 120v 1.5amp motor used for the 112T/V (112 Series) pump head.
- PumpTec
- 1/7HP
- 120V
- For Use with 112T/V Pump Head
$217.46 -
PumpTec Series 205, 207 Kit BPumpTec 205 and 207 check valve kit, kit B.
- PumpTec
- Kit B Check Valves
- Series 205 and 207 Pump Heads
-
Ametek M53 Upgrade Short Base Motor (B4CPM‑164)M53 Short Base Motor.
- Ametek
- 12VDC with Rectifier
- For Use with PumpTec Series 205/207 Pumps
$329.95 -
Ametek 2 Stage Vacuum Motor (116392‑00)
2 Stage Vacuum Blower for dual vacuum units. Unit has 5.58” diameter motor with 80” of water lift. This fits many Ninja Deluxe units after serial #C14855 and Ninja Deluxe units with heat after serial #PH2094 and other units containing dual 2 stage motors.
- 2 stage vacuum motor
- 5-5/8” diameter
- 80” water lift
- Lamb # 116392-00
$125.09 -
ea Blower GasketThis gasket fits the 5-5/8" vacuum motors.
- Foam
- For use with 5-5/8" vacuum motors
- Self Adhesive
-
Valve, Drain 1 1/2"
1-1/2" Drain Valve including the spout and gasket.
- Plastic Drain Valve-1-1/2”
- Includes the Spout and Gasket
-
Century 400 Manual Temp Reset Switch (130‑14C)
Ninja Classic heater resettable thermostat
- Century 400
- Resettable Thermostat
- For Century Ninja Classic Heater
-
Coupler, 1/4"FPT x 1/4"FQD
The most common female quick disconnect for the carpet cleaning industry. The 1/4", brass, female coupler is equipped with double EPDM seals which are resistant to high pressure, high temperature, all but solvent based chemicals and abrasion.
- Double EPDM O-Rings
- Brass Construction
- 1/4"
-
Castex/Nobles/Tennant Filter Solution Tank (180628)
Mushroom shaped stainless steel filter for solution tank.
- 100 Mesh
- Stainless Steel
- Mushroom Filter
-
Axle for 500PSI Ninja
Axle for 500PSI Ninja
- Axle for 500PSI Ninja
$135.72 -
Wheel, 4" Swivel Caster
New style 4" swivel caster.
- 4"
- Swivel
- Steel Base
- Non Marking Grey Wheel
-
Wheel Rear Ninja, 10"
This wheel fits the Century Ninja Extractors that use 10-inch wheels with a 1/2 inch shaft.
- Wheel Rear Ninja 10"
-
Relief, 12 Gauge Cord Strain
Strain Relief 12 Gauge made from heavy duty plastic.
- Strain Relief
- 12 Guage Cord
- 1/2" Male Thread
- Fits Most Portable Extractors
-
Draw Latch Assembly
Draw Latch
- Easy to install
- Fits Ninja 400 series units
-
Single Carbon Brush
Carbon Brushes
- Carbon Brush
- Sold Individually
- For Use with Century Ninja