Please select a Shopping List

SCHÖNOX® US Cement Based Self‑leveling Compound

  • EMICODE EC 1PLUS R: very low emission
  • For interior and exterior use
  • Water- and frost resistant
  • Self-leveling, low shrinkage
  • Coverage: approx. 55–65 sq ft per unit at a thickness of 1/8"
Grouped product items
Product Name Price Qty
SCHÖNOX® US Cement Based Self‑leveling Compound, 55 LBS
Item # EX-SCHUS-55
Mfr. Model # 55# SCHöNOX US
55 Lbs     Qty: 1
Availability: Typically in stock (Details)
Add to My Shopping List
$34.56
Description

Product Information

SCHÖNOX US is a cement-based self-leveling compound designed for use on cement- and gypsum-based substrates. This compound is designed for fast leveling in interior and exterior areas. It can be installed above 1/8” up to 3”.

 

SCHÖNOX US is water- and frost-resistant and may be used on both interior and exterior surfaces. It has no moisture vapor emission limitations on properly prepared concrete.

 

This low-shrinkage, pumpable compound is easy to apply. Users can layer thicknesses above 1/8“ up to 1.5“ without aggregates or layer thicknesses up to 3“ with aggregates.

 

SCHÖNOX ZM exceeds minimum Ff/Fl requirements of ASTM and ACI when installed in accordance with the guidelines. It has been tested in accordance with ASTM C1708.

 

This compound is rated EMICODE® EC 1PLUS R for very low emissions. It is suitable for castor wheel loadings above 1/16“ according to DIN EN 12529.

 

SCHÖNOX US is suitable for use on:

  • Concrete, cement substrates
  • Rapid-drying cement screed systems
  • Gypsum substrates
  • OSB board, plywood (well screwed or bonded) prior to installing flexible coverings
  • Old substrates, such as ceramic tiles and terrazzo
  • Old, water-resistant adhesive residues

 

SCHÖNOX US is suitable for filling, smoothing and leveling of substrates under:

  • Flexible coverings
  • Wood floors, layer-thickness above 1/4” (interior only)
  • Ceramic tiles
  • Underfloor heating systems

 

SCHÖNOX US can also be used for filling, smoothing, and leveling of unheated, cement-based substrates under SCHÖNOX Moisture Mitigation Systems.

 

Key Specifications:

  • Pot Life: Approx. 40 minutes at 68°F
  • Ready for Foot Traffic: Approx. 4 hours
  • Ready for Covering:
    • For floor covering products: After approx. 24 hours up to 1/4" thickness, after 48 hours up to 3/8” thickness
    • For tile or stone: after approx. 4 hours
  • Working Temperature: Not below 41°F
  • Environmental Product Declaration (EPD): EPD-DIV-2013311-EN
  • LEED—May help contribute to LEED certification of projects in the following categories:
    • EQc2: Low-Emitting Materials – 1 to 3 points
    • MR Credit 1.1: Building Reuse-Maintain – Existing Walls, Floors and Roof – up to 3 points
    • MR Credit 1.2: Building Reuse-Maintain – Existing Interior Nonstructural Elements – 1 point
  • VOC Content: 0g/l (calculated), SCAQMD 1113
  • Shelf Life: 12 months, unopened
  • Coverage
    • Approx. 55–65 sq ft per unit at a thickness of 1/8” (depending on substrate conditions and aggregate used)
  • Compressive Strength (ASTM C109):
    • 4,250 PSI / 25 N/mm² / 300 kg/cm2 after 28 days
    • 2,000 PSI / 12 N/mm2 / 135 kg/cm2 after 1 day
  • Flexural Strength (ASTM C348): Approx. 1,000 PSI / 6 N/mm² after 28 days
  • Tensile Strength (ASTM C1583) at 1/8”: Above 350 PSI / 2 N/mm2 after 3 days
  • Initial Set (ASTM C191): Approx. 80 minutes
  • Final Set (ASTM C191): Approx. 95 minutes
  • UL-classified in accordance with ASTM E84 (ANSI/UL 723): Flame Spread 0; Smoke Development 0

 

*All values are approximate, are subject to local climatic fluctuations based upon conditions at 70°F with atmosphere of less than 65% relative humidity following the recommended mixing ratio. Do not install underlayment or topping before the substrate has dried thoroughly

Usage

Usage

Mixing Ratio:

Mix each 25kg/55 lbs bag with 4.5 liters/4.7 quarts of water

 

If SCHÖNOX US is extended with dry, clean aggregate (aggregate is added last) at a layer thickness of 1.5”–3“, type and amount of aggregate used will affect product performance. As qualities of locally available aggregates vary, we recommend performing tests prior to use on a larger scale.

 

Do not overwater! Foam while mixing, or settling of the sand aggregate while placing, indicates overwatering.

 

Recommended Working Method:

  1. Using a clean mixing drum, add SCHÖNOX US to cold, clean water to form a homogeneous mixture.
  2. Mix thoroughly for approx. 3 minutes using a heavy-duty drill (min. 600 RPM) is recommended to obtain a lump-free mix.
  3. Pour the mix and spread using a smoothing trowel. Even surfaces are easily achieved using a pin leveler. In higher thicknesses using a spike roller is recommended. Contact to vertical structures should be avoided by putting in an edge strip.
  4. If a second layer of leveling compound is to be applied, prime the first layer with SCHÖNOX VD (diluted 1:1 with water) after drying. The maximum layer thickness must not be exceeded in case of two-layer applications. The second layer must not exceed the layer thickness of the first layer.
  5. Protect curing SCHÖNOX US layers from high ambient temperatures, direct sunlight, and draughts.
  6. Clean tools in water immediately

 

Specs

Specifications

More Information
Brand Schönox
Category Concrete Patch
Condition New
Manufacturer Model Number T47 - Silica Aggregat
Safety Data Sheet (SDS)
Related Products

Customers Also Viewed