Please select a Shopping List
Your company account is blocked and you cannot place orders. If you have questions, please contact your company administrator.

Scanmaskin Scan Combiflex 650 DSP Floor Grinder

Item #
Send to a Friend Add to My Shopping List
  • Productivity rates of 650–970 square feet per hour
  • Available in 480V and 230V configurations
  • Solid steel construction—right down to the dust shroud
Store Pickup Not Available

Product Information

The Newest in "Smart" Grind Technology from Scanmaskin


Unveiled at the World of Concrete 2016, the Scan Combiflex 650DSP is a new type of concrete floor grinder unlike anything the industry has seen before. This machine is engineered with an integrated computer system and smart floor grinding and polishing technology that guides you through the entire job, virtually eliminating all guesswork from the grinding and polishing process.


The Scan Combiflex 650 DSP features a built-in touch display that shows diamond tool wear, tool lifetime, machine speed, and power consumption. It provides recommendations for the kind of tool that should be used on the machine as well as the speed to reach optimal wear. The 650DSP has pre-programmed hardness settings that correspond to the Mohs scale hardness readings from the floor. It then calculates the speed necessary to reach as optimal a performance as possible. It also features a gauge that gives you an estimate as to how much time is left before the tool needs to be replaced.


A series of sensors throughout the machine continuously transmits data, providing operators the critical information they need to do the job right. Instead of completing a job only to discover that it could have been done better, the 650 DSP provides clear recommendations and warnings so you can make the right decisions at the right time.


With a 26-inch grinding path and a weight topping 705  lbs, the 650 DSP is ideal for large commercial applications. Like all Scan Combiflex floor grinders, the 650 DSP is engineered to direct the torque of the machine at the floor—not at the operator’s hip. This allows the 650 DSP to grind or polish at higher speeds with minimal vibration and stress.


Are you using the right dust collector?

Additional Info

Additional Info

Model: 230 Volt, Single Phase

  • Motor Size: 5 hp
  • Amps: 29 Amps
  • Frequency: 50/60 Hz ± 5%
  • Internal Fuse: 32Amps
  • Standard Power Inlet: IEC 60309 3P+N+E 400V 16A


Model: 230 Volt, Three Phase

  • Motor Size: 10 hp
  • Amps: 27 Amps
  • Frequency: 50/60 Hz ± 5%
  • Internal Fuse: 32 Amps
  • Standard Power Inlet: IEC 60309 3P+E 250V 32A


Model: 380 Volt, Three Phase

  • Motor Size: 10 hp
  • Amps: 15.3 Amps
  • Frequency: 50/60 Hz ± 5%
  • Internal Fuse: 16 Amps
  • Standard Power Inlet: IEC 60309 2P+E 250V 32A


More Information
Amps16 Amps
Weight705 Lbs
RPMs300 - 1100
Powered ByElectric
CategoryFloor Grinders
Operating SpeedsVariable
Warranty InformationThis product from Scanmaskin Sweden AB comes with a twelve month warranty. If the product does not function satisfactorily during this period, Scanmaskin will return the product to full working order for normal use which the product is intended for – with no charge for labor or spare parts, according to the following conditions:

1. The warranty only applies to persons that have legal right to the equipment during the warranty period.

2. The manufacturer's undertaking is limited to the repair of defective parts or the replacement of these according to the manufacturer's assessment. Costs and risks for transport as well as dismantling and reinstallation of the product / products and other direct or indirect costs, associated with the repair in question, are not covered by this warranty.

3. Periodic inspections, adjustments, maintenance work and changes are not covered by the warranty.

4. Scanmaskin is not liable for any damages to grinding discs or other similar equipment. original components, or incorrect use and installation.

5. The warranty only applies to material and design deficiencies and does not apply in the following cases:
a. Damage caused through accidents, carelessness, changes, use of spare parts or grinding tools that are not original components, or incorrect use and installation.
b. Damage caused by lightning, water, fire, vandalism, incorrect mains voltage, incorrect ventilation or other causes that lie outside of the manufacturer's control.

6. Scanmaskin reserves the right to modify the design – or make improvements without obligation to change previously manufactured products.

7. All warranty repairs must be carried out by Scanmaskin or by a Scanmaskin authorized repair workshop. Costs for repairs, carried out by an unauthorized workshop, will not be reimbursed by Scanmaskin. If such repairs damage this product these are not cover by the warranty agreement.
Manual / Schematic
Related Products

Customers Also Viewed