Phoenix 200 Max Replacement Parts
Exhaust blower for the Phoenix 200 and 200 Max.
- Replacement exhaust fan
- Fits Phoenix 200, 200 Max and 300 dehumidifiers
The Phoenix Solution LGR performance amplifier widens the effective operating range of LGR dehumidifiers, increases grain depression and improves water removal rates to 100%.
- Removes water in drying conditions up to 140°F
- Accelerates the drying process by an amazing 33%
- Intercooler pre-cools incoming air stream
- Nests into the Phoenix 200 Max, 200HT, and Ultimate 340
- Only draws 1.6 amps
This pre-wired condensate pump by Therma-Stor LLC is designed for use with a selection of the Phoenix line dehumidifiers, including the 200 MAX, 200 HT, 270HTx, as well as the Jon-Don Ultimate 340.$147.33
120VAC 30A relay.
- 120V Relay
- Ships Same Day
This filter provides an excellent combination of rugged construction, high-quality performance, and low initial cost. It is not reliant on electrostatic charge for efficiency. It offers low resistance to airflow and has a high dust-holding capacity.
- Sturdy double-wall frame design
- Moisture resistant beverage board frame
- Listed Size: 16 x 20 x 2 inches
- Nominal Size: 15.5 x 19.5 x 1.75 inches
- Standard filter for the Ultimate 340 and most Phoenix stainless dehuidifiers
Starting at: $5.48
This filter offers superior construction and is an optional filter upgrade for many Phoenix LGR dehumidifiers.
- MERV 14, 95% efficiency
- Listed Size: 16 x 20 x 4 inches
- Nominal Size: 15.5 x 19.5 x 3.75 inches
- Optional Filter Upgrade for Most Phoenix Stainless Dehumidifiers
Phoenix rigid handle assembly.
- Rigid Aluminum Handle Assembly
- Comes with Plastic End Caps
ea strain relief for 200 Max$2.00
ea Defrost Timer for PH-P200 and P200P$44.44
Power cord fits many Phoenix/Thermastor units.$36.53
ea Thermostat Control PH-P200$31.21
These couplers are typically used on the 1/4" drain hoses for most dehumidifiers. This coupler is a 1/4" open flow, Acetal, free float mounting, male insert. It can withstand temperature ranges between -40° and 180°F.
- 1/4" hose barb
- Male coupler
- For use with Jon-Don Ultimate 340 and Phoenix 200Max dehumidifiers
These couplers are typically used on the 1/4" drain hoses for most dehumidifiers. This coupler is a 1/4" open flow, Acetal, free float mounting, female receptacle. It can withstand temperature ranges between -40° and 180°F.
- 1/4" hose barb
- Female coupler
- For use with Jon-Don Ultimate 340 and Phoenix 270HTX/200HT/200Max dehumidifiers
ea evaporator coil R-410$144.86
Non marking black rubber wheel with plastic rim, measures 12" in diameter with a 1/2" axle hole. Used on many of the Phoenix LGR style dehumidifiers.$20.88
Momentary style purge switch for Phoenix 200, 200Max, 200HT, 300 dehumidifiers. Also works with the Ultimate 340.
- Replacement purge switch
- Spring loaded to turn off when released
- Fits most Phoenix dehumidifiers
- Replacement power switch
- Fits most Phoenix dehumidifiers and air scrubbers
Low Pressure Control Switch fits most Phoenix commercial dehumidifiers, including models #200, #200Max, #200HT, and #300.
- Replacement low pressure switch
- Must have licensed A/C repairman replace
Rubber Stopper (Foot)
- Replacement rubber foot
- Fits 200 Max and Guardian HEPA air scrubbers
This exhaust collar fits a selection of Phoenix air scrubbers and dehumidifiers.$3.18
This condensate pump vinyl drain hose measures 1/4"ID x 33'L.
- Condensate pump vinyl drain hose
- Measures 1/4"ID x 33'L
- Commonly used on Phoenix dehumidifiers