Ninja Dual 3 Stage 200/500 PSI Replacement Parts
This Flow Control K-Valve is rated at pressures up to 500 PSI. This part is easily rebuildable.
- High-quality replacement part
- Withstands pressures up to 500 PSI
- Easily rebuildable
This 207 Gold Series pump replaces the 205 series. This complete pump assembly has a 120V, 1/3 HP motor and provides an adjustable 500 PSI. It pumps at a rate of 1.4 GPM at 500 PSI and can withstand a maximum of 160°F of water inlet temperature.
- Replaces 205 series pump
- Adjustable 500 PSI
- Complete pump and motor
- 1/3 HP; 3.0 /1.5 amps
- 1.4 GPM at 500 PSI
PumpTec 205 Series pump head without motor.
- Motor not included
The Pumptec 112T series pump features an efficient plunger-type design that produces up to 20% more pressure or flow for a given power input compared to competitive pumps. This pump is ideal for pressure cleaning, pest spraying, and misting applications.
- Plunger-type design for ultimate pumping efficiency
- 200 PSI
- Four 1/4” ports
- Non-Viton Buna seals
- 120 volt
Pump Head PumpTec 112 Series without motor.
- Series 112T Pump Head
- 200 PSI
M35 1/7HP 120v 1.5amp motor used for the 112T/V (112 Series) pump head.
- For Use with 112T/V Pump Head
PumpTec 205 and 207 check valve kit, kit B.
- Kit B Check Valves
- Series 205 and 207 Pump Heads
This 3-stage Ametek 5 5/8” dia 90 CFM 112" H2O lift, 10.6A
- 3-stage; 10.6 amps
- 5 5/8” diameter
- 99 CFM; 112" water lift
- Lamb #116565-13
M53 Short Base Motor.
- 12VDC with Rectifier
- For Use with PumpTec Series 205/207 Pumps
This gasket fits the 5-5/8" vacuum motors.
- For use with 5-5/8" vacuum motors
- Self Adhesive
Toggle Switch Boot
- Rubber Toggle Switch Boot
Ninja Classic heater resettable thermostat
- Century 400
- Resettable Thermostat
- For Century Ninja Classic Heater
OEM panel mounted pressure gauge 0-600 PSI.
- Century 400
- 0-600 PSI
- 1/4" MPT
The most common female quick disconnect for the carpet cleaning industry. The 1/4", brass, female coupler is equipped with double EPDM seals which are resistant to high pressure, high temperature, all but solvent based chemicals and abrasion.
- Double EPDM O-Rings
- Brass Construction
1-1/2" Drain Valve including the spout and gasket.
- Plastic Drain Valve-1-1/2”
- Includes the Spout and Gasket
Mushroom shaped stainless steel filter for solution tank.
- 100 Mesh
- Stainless Steel
- Mushroom Filter
Wheel Black Ninja 12"$78.60
Elbow 1.5 FS x 1.5 FPT
- 1.5 pvc elbow fitting
500 psi Pressure Regulator with adjustable rating of 50-500 psi .
- Brass Regulator
- Adjustable 50-500 psi
- Carbon Brush
- Sold Individually
- For Use with Century Ninja
- Easy to install
- Fits Ninja 400 series units
Strain Relief 12 Gauge made from heavy duty plastic.
- Strain Relief
- 12 Guage Cord
- 1/2" Male Thread
- Fits Most Portable Extractors
Power Cord 14 Gauge
- Power Cord 14 Gauge
This wheel fits the Century Ninja Extractors that use 10-inch wheels with a 1/2 inch shaft.
- Wheel Rear Ninja 10"