Scanmaskin Scan Combiflex 800DSP Floor Grinder

Item # FG-SM800DSP-EA

Hover Over Image to Zoom
More Views
Scanmaskin Scan Combiflex 800DSP Floor Grinder

Item # FG-SM800DSP-EA

Store Pickup Not Available

  • Integrated computer and touch-screen display
  • Measures diamond tool wear in real time so the operator can make adjustments
  • 32" grinding path; 882 lbs weight
  • Production rates of 750–1,290 square feet per hour
  • 230V and 480V models available

Product Information

Concrete Grinding Just Got a Whole Lot Easier!


The Scan Combiflex 800DSP is a new type of concrete floor grinder unlike anything the industry has seen before. This machine is engineered with an integrated computer system and smart floor grinding and polishing technology that guides you through the entire job, virtually eliminating all guesswork from the grinding and polishing process.


The Scan Combiflex 800DSP features a built-in touch display that shows diamond tool wear, tool lifetime, machine speed, and power consumption. It provides recommendations for the kind of tool that should be used on the machine as well as the speed to reach optimal wear. The 800DSP has pre-programmed hardness settings that correspond to the Mohs scale hardness readings from the floor. It then calculates the speed necessary to reach as optimal a performance as possible. It also features a gauge that gives you an estimate as to how much time is left before the tool needs to be replaced.


A series of sensors throughout the machine continuously transmits data, providing operators the critical information they need to do the job right. Instead of completing a job only to discover that it could have been done better, the 800DSP provides clear recommendations and warnings so you can make the right decisions at the right time.


With a 32-inch grinding path and a weight topping 882 lbs, the 800DSP is ideal for large commercial applications. Like all Scan Combiflex floor grinders, the 800DSP is engineered to direct the torque of the machine at the floor—not at the operator’s hip. This allows the 800DSP to grind or polish at higher speeds with minimal vibration and stress.



  • Productivity Rates: 750–1,290 sq ft/hr
  • Voltage Choice: 230V 3-phase; 480V 3-phase
  • Grinding Path: 32 inches
  • Motor: 11 kW
  • Amps: 32
  • Frequency: 50/60 Hz
  • Motor Type: Planetary drive system
  • Speed: 500–1,100 RPM
  • Tools: Holds up to 18
  • Weight: 882 lbs


Volts 230/460
Amps 32
Weight 880
RPMs 500 - 1000
Brand Scanmaskin
Condition New
Diameter (in.) 32
Powered By Electric
Horsepower 10
Category Floor Grinders
Operating Speeds Variable
Electrical Phase Three
Warranty Information This product from Scanmaskin Sweden AB comes with a twelve month warranty. If the product does not function satisfactorily during this period, Scanmaskin will return the product to full working order for normal use which the product is intended for – with no charge for labor or spare parts, according to the following conditions:

1. The warranty only applies to persons that have legal right to the equipment during the warranty period.

2. The manufacturer's undertaking is limited to the repair of defective parts or the replacement of these according to the manufacturer's assessment. Costs and risks for transport as well as dismantling and reinstallation of the product / products and other direct or indirect costs, associated with the repair in question, are not covered by this warranty.

3. Periodic inspections, adjustments, maintenance work and changes are not covered by the warranty.

4. Scanmaskin is not liable for any damages to grinding discs or other similar equipment. original components, or incorrect use and installation.

5. The warranty only applies to material and design deficiencies and does not apply in the following cases:
a. Damage caused through accidents, carelessness, changes, use of spare parts or grinding tools that are not original components, or incorrect use and installation.
b. Damage caused by lightning, water, fire, vandalism, incorrect mains voltage, incorrect ventilation or other causes that lie outside of the manufacturer's control.

6. Scanmaskin reserves the right to modify the design – or make improvements without obligation to change previously manufactured products.

7. All warranty repairs must be carried out by Scanmaskin or by a Scanmaskin authorized repair workshop. Costs for repairs, carried out by an unauthorized workshop, will not be reimbursed by Scanmaskin. If such repairs damage this product these are not cover by the warranty agreement.