You get free shipping on this item!
How can I get free shipping on this item?
Struggling to Remove Mold Stains? Try Concrobium Mold Stain Remover!
No brushing, sanding, or blasting required!
Mold stains are difficult to remove and pose a challenge to even the most experienced restoration professional. Concrobium Mold Stain Remover was developed specifically to remove mold stains without the need for brushing, sanding, or blasting (dry ice or soda). There’s no scrubbing and no cleanup, either. Just wet the surface and allow it to dry. Most surfaces require just a single application.
Concrobium Mold Stain Remover employs liquid oxidative technology to facilitate physical mold removal, but without the harsh chemicals associated with traditional oxidation products. There’s no chlorine, no hydrogen peroxide, and no harmful residues. After use, the product breaks down into oxygen and water.
This unique, non-foaming solution quickly and easily removes the toughest mold stains on a wide range of surfaces. It physically separates mold from the surface, enabling full remediation.
Concrobium Mold Stain Remover can be applied with any standard sprayer, so you don’t need to invest in any special equipment or training. This product can be applied on most hard, non-porous or semi-porous surfaces, such as wood and composite wood, concrete, masonry, drywall, grout, fiberglass, tile, plastic laminate, and metal.
Ideal for use in:
- Commercial and industrial buildings
- Anywhere mold stain removal is required!
Test in an inconspicuous area before use.
Regular (20.6 oz): 300-400 square feet of coverage
Small (8 oz): Approximately 100 square feet of coverage
Concrobium Mold Stain Remover is part of the Attic Attack! approach to crawlspace and attic mold remediation. Attic Attack! is consistent with the industry Standard of Care, and can reduce project costs by 65%. Instead of blasting, scraping, or sanding, Attic Attack! relies on Concrobium Mold Control along with Concrobium Mold Stain Remover to effectively eliminate mold and treat tough mold staining.
The Attic Attack! method of mold remediation and control has been shown to deliver results that are as good as, if not better than, traditional sanding procedures.
To learn more about Attic Attack!, contact your Jon-Don Restoration Sales Representative at 800-556-6366.
Here's what our customers have to say...
"Over the past few months I have had the opportunity to use Concrobium Mold Stain Remover on a few of our projects. In this short time, I am very impressed with the success we have had on a number of projects. The ability of this product to remove the staining caused by mold/mildew and leave our customers with a superior looking finish project is a BIG PLUS with customer satisfaction. Our technicians like the product over conventional sanding or blasting…it's safer and faster, and that equals savings to the bottom line. From wood, to cement, to siding...you will be impressed with the results.
- Craig Kersemeier
- Mix both containers with warm water, stirring regularly
- Wait 30 minutes after mixing with water to allow sufficient time for stain removal agent to be generated
- Use within 2 hours of initial mixing
- Just wet surface using a pump up or airless sprayer and allow to work – tough stains may require up to 24 hours to disappear
- Recommended to be used in conjunction with Concrobium Mold Control to prevent mold growth
The greater the extent of the mold growth, the more important surface saturation is and the longer the dwell time required on the surface.
The best results are seen when the solution is applied where surface temperatures are above 50○F or 10○C. Avoid direct sunlight and ensure that the product is mixed with warm to hot water (80-100○F or 27-38○C). Prior to using Concrobium Mold Stain Remover ensure that the surface has been cleaned of dirt and debris and maximize the surface dwell time to increase product efficacy.
Brand Concrobium Category Mold Stain Removers Product Type Powder Scent Fragrance Free pH 10.5 Material Concrete, Drywall, Fiberglass, Metal, Plastic, Tile, Wood Application Concrete, Drywall, Mold Remediation, Water Damage Restoration Application Method Spray Approved Use Mold Remediation, Water Damage Condition New Xactimate Code HMR GRMS
- Related Products
Customers Also Viewed