You get free shipping on this item!
How can I get free shipping on this item?
Next Generation Mold-Resistant Coating!
IAQ 6000 GEN3 is formulated with a unique fungistatic agent to resist mold growth on the dry coating surface. IAQ 6000 GEN3 is a white, tintable mold-resistant coating for professional use.
IAQ 6000 GEN3 is a durable, flexible, and permeable 100% acrylic water-based coating.
IAQ 6000 GEN3 has been tested by independent and certified laboratories to prove resistance to mold growth on the surface of the coating, and has successfully passed ASTM G-21 mold resistance testing with the highest possible score.
IAQ 6000 GEN3 is recommended for use on wood, plaster, wallboard, sheetrock, concrete, masonry block, primed metal and galvanized metal. IAQ 6000 GEN3 can also be used on new structural materials during building construction.
*Resists mold growth on the dry coating surface only.
VOC compliant in US and Canada.
- Solids by Weight ± 2%: 50.2%
- Solids by Volume ± 2%: 34.6%
- Viscosity at 70° F: 95-100 Kreb Units
- Specular Gloss: 5-6° ± 1 @60°
- Flash Point: Non-combustible
- Shelf Life: 24 Months Min. (Original Sealed Container)
- Calculated VOC: 0 Grams/liter
- Smooth Surfaces: 250-400 ft2/gal
- Porous Surfaces: 150-300 ft2/gal
- Drying Times (@ 70-77° F, 50% R.H)
- To Touch: 1 hour
- To Recoat: 4 Hours
- Minimum Application Temp: 50°F (10°C)
Warning! If you scrape, sand, or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424- LEAD (5323) or log on to www.epa.gov/lead.
Surfaces to be coated must be free of dust, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, and other surface contamination. Clean mold-stained surfaces with IAQ Advanced Peroxide Cleaner, or use an EPA-registered antimicrobial disinfectant cleaner, such as IAQ 2000, IAQ 2500, ShockWave, or ShockWave RTU.
Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6000 ZERO is self-priming over bare sheetrock, composition board, ceiling tile, and concrete.
WALLBOARD, SHEETROCK, GYPSUM BOARD - Joint cement should be sanded smooth, but avoid abrading the paper.
FERROUS METAL - Clean, then prime with IAQ 4000 rust-inhibiting direct-to-metal primer.
WOOD - Seal knots and stains with IAQ 5000 stain-blocking primer.
MASONRY BLOCK - Apply one coat of IAQ 3000 block filler if a denser surface is desired.
Apply IAQ 6000 ZERO with a brush, roller, or airless spray equipment.
- Brush: Synthetic, nylon, or polyester bristle
- Roller: Synthetic fiber 3/8” nap or longer
- Spray Settings:
- Pressure: 2,000-3,000 PSI
- Tips: 0.019 to 0.021 tips
- Xactimate Information
Xactimate Code: PNT S+++ - Seal the walls and ceiling with an antimicrobial coating - One coat
Brand Fiberlock Category Coatings Color White Approved Use Mold Remediation, Water Damage Max Coverage Per Gallon 400 Application Concrete, Drywall, Mold Remediation pH 8..5 Condition New Xactimate Code PNT S+++ - Seal the walls and ceiling with an antimicrobial coating - One coat
- Related Products
Customers Also Viewed